Questions?
We’ve got answers.

Flagrings are independently rotating flagpole attachment rings built around sealed, 100% zirconia ceramic ball bearings. Every Flagrings product uses ceramic bearings, including both solid-metal and 3D-printed models. They let the upper and lower attachment points turn with changing wind so a grommeted flag has a better chance to rotate around the pole instead of winding tightly around it.

Wrapping usually starts when one or both attachment points bind under the flag’s weight. Flagrings use low-friction, sealed 100% zirconia ceramic bearings so each attachment can rotate independently under load. That helps the flag follow a change in wind direction and, after a brief wrap, gives it a better chance to unwrap itself when the breeze returns.

No honest spinner can promise that. A sudden lull, gust, downdraft, or wind reversal can temporarily fold almost any flag around a pole. Flagrings reduce binding at the attachment points, but pole angle, flag size and weight, spacing, nearby walls or branches, and local airflow all affect performance.

A plain plastic-on-plastic or metal-on-metal ring may spin when empty but drag once the flag pulls down on it. A sealed, 100% zirconia ceramic ball bearing reduces rotational resistance under real load while helping keep dirt and moisture away from the moving parts.

They can help reduce avoidable wear. Smooth rotation and properly spaced attachments reduce friction, twisting, and stress at the grommets and reinforced heading. Flag material, weather exposure, pole clearance, and correct sizing still matter.

Choose direct-mount when the same flag stays up for long periods. The flag attaches directly to the swivels, giving you a cleaner, quieter setup with fewer separate parts.

Choose clip-on when you change flags often. Extra-large stainless-steel clips make seasonal, military, or decorative flags faster to swap, and the vertical eyelet lets each clip hang naturally.

Every Flagrings swivel now uses sealed, 100% zirconia ceramic bearings for smooth, low-friction rotation and maximum corrosion resistance. Ceramic is the only option across the entire product line, including all solid-metal and 3D-printed Flagrings.

Yes. The entire ceramic bearing is made from 100% zirconia ceramic, so the ceramic bearing cannot rust. Other exposed hardware should still be inspected and cared for based on the product configuration and your environment.

The Flagrings line includes heavy-duty UV-rated 3D-printed swivel rings and solid machined-metal configurations, with direct-mount and clip-on choices depending on the listing. Every construction uses the same type of sealed, 100% zirconia ceramic bearings. Check the selected product page for its exact body material, hardware, color, size, and availability.

Black and silver finishes are offered on selected configurations. Availability varies by product and size, so use the color selector on the product page to see the current combination available for your pole. Every color and construction uses sealed, 100% zirconia ceramic bearings.

A standard set includes two Flagrings—one upper and one lower—enough for one typical flag with two grommets. Clip-style sets include the heavy-duty stainless-steel clips; direct-mount sets attach the flag without separate clips.

Current core sizes are 1″, 1.25″, 1.5″, 1.75″, and 2″, measured by the pole’s outside diameter at the exact location where the ring will sit.

Measure the outside diameter—never the circumference and never the advertised pole length. A caliper is ideal. For an installed pole, use the cardboard-notch method:

1. Cut a small notch in a scrap of cardboard.
2. Slide it onto the pole where the swivel will sit.
3. Enlarge the notch until it fits snugly.
4. Measure the width of the notch with a ruler or tape.

For pictures and step-by-step help, visit our complete flagpole measuring guide.

If the measurement falls between sizes, ask before ordering.

Flagrings fit many common residential, commercial, RV, and trailer-mounted poles, including many SunSetter, Flagpole Buddy, and Costco setups. Brand name alone does not guarantee fit—verify the outside diameter where each ring will operate.

Measure the exact section where each ring will rotate. Make sure joints, collars, buttons, taper changes, brackets, and finials do not block a complete turn. The upper and lower mounting points may sit on sections with different diameters, so measure both.

Lower the pole to a safe working height. Slide the correctly sized upper and lower rings onto the pole, position them to match the flag’s grommets, and secure the integrated stainless-steel screws. Attach the flag directly or with the included clips, depending on the style. Confirm both rings rotate freely before raising the pole.

Match the grommet spacing so the flag’s reinforced heading is supported but not stretched drum-tight. Too much tension adds friction and distortion; too little spacing allows sagging and bunching. Make small adjustments and observe the flag through several wind conditions.

Yes, if the pole and bracket are rated for the combined wind load. Give each flag independent rotating support when possible and enough separation to prevent continuous rubbing. Avoid hanging two flags from one overloaded upper swivel, which can bind and make the flags drag each other around the pole.

Lightweight nylon lifts in gentler breezes and often responds faster when wind direction changes. Heavier polyester can be durable in stronger winds, but it adds load and may need more airflow to lift and unwrap. The best choice depends on the pole, angle, flag size, and local wind.

Yes. A larger flag adds wind load, attachment load, and more fabric that can wrap around the pole. For many common wall-mounted poles at roughly 45°, a 2.5′ × 4′ flag may behave more freely than a heavier 3′ × 5′ flag. Always match the flag to the pole, bracket, and exposure.

Yes, with proper care. Every model uses sealed, 100% zirconia ceramic bearings, making the ceramic bearings fully rust-proof and especially well suited to persistent salt-air or wet environments. Salt can still affect exposed hardware, so inspect it regularly and rinse away salt deposits with fresh water when appropriate.

Sealed, 100% zirconia ceramic bearings are designed to keep their operating surfaces protected from contaminants; routine external lubrication is not normally needed. Do not spray the ceramic bearings with oil unless the instructions for your exact product recommend it—excess lubricant can attract dirt. If rotation changes, contact Flagrings for specific guidance.

Periodically check that both rings turn freely, fasteners remain secure, and nothing has shifted into a pole joint, bracket, or taper. Do not overtighten set screws. In salt air, rinse exterior surfaces when appropriate and inspect more often. Replace a waterlogged, badly frayed, or overly heavy flag before blaming the hardware.

Flagrings address rotation; they do not increase the wind rating of your flag, pole, bracket, or wall mounting. Remove the flag when conditions exceed any component’s rating or during severe weather. Also keep a full circle of clearance from roofs, gutters, walls, trees, and other flags.

Flagrings products are made in the USA. Founder Giuseppe Giannola designed them after getting tired of rings that tangled, snapped, or wore out, and he remains the person customers reach for product support.

Shipping is free on all orders. Orders placed before 1 PM Eastern / 10 AM Pacific are scheduled to ship the same business day from California. Carrier travel time begins after dispatch and varies by destination.

Flagrings backs orders with a 100% satisfaction-or-money-back guarantee. If you order the wrong size and return or exchange it for sizing reasons, you are responsible for the needed shipping costs—which is why measuring first matters.

Email founder Giuseppe directly at g@flagrings.com. Include your pole’s outside diameter, where the rings will sit, and a photo of the setup when possible. You can also use the contact page.